Home ꄲ Log debarking machine ꄲ Main parameters of the hydraulic debarker

ꁆ ꁇ

Main parameters of the hydraulic debarker

ꄴPrevious： null

ꄲNext： null

넳 넲

All categories

Plywood equipment

type		BXAY1915(/5)		BXQY1927(/5)
length of the rotary knife		1400mm		2700mm
max length of the wood to be debarker		1300mm		2600mm
power of the main motor		15KW(22KW)		15KW(22KW)
power of the ofl pump		4KW		5.5KW
total power		19KW(26KW)		27.5KW
nax.dlaneter of the wood to be debarker		≤φ360mm(500)		≤φ400mm
min.dlameter of the wood to be debarker		≤φ80		≤φ80
size.length×width×height(mm)		3300×220×1850		5600×2200×1850
net weight(kg)		约4200 about4200		约6700 about6700

BG18SERIESINJECTINGMESH-BELTVENEERDRIER

Thismachineisoneofthemainmachineinplywoodproductionline.Itisusedtodrytheveneer

PT12 Series CNC Fluoroplastic Rotary Cutting Machine

BC3325AUTO- TRIMMER

This machineis one ofthe main equipmentsin artificial board productionine.lt cancutthe edge crosswise and lengthwiseto getthe artificial board with size needed .

BY21 SERIES TRANSVERSE FRAME FRAME HOT PRESS

This machine is a main machine in plywood production line，It is used to hot-press combine the mat which after glue-spreading combination.

BY81SERIESPRE-COMPRESSOR

This pre-compressor is an auxiliary machine in the plywood production line.it can pre-press the glued veneers which are made into mat and make them fall into a pattern.It is an important machine to raise the quality of plywood.

Main parameters of the hydraulic debarker

BJ11 VENEER CLIPPERS

This machine is used to cut the whole veneer and to trim their edges.

BJB11 SERIES ELECTRIC VENEER REELING MACHINE

This machine is used to roll the veneer made form the wood after being cut and it is matched with common veneer lathe.

BD1513-27 OPTICAL CENTERING MACHINE

This machine has high precision and easy operation characteristic and it can reduce the insecure factor during the productive process.

BJ1327 MAIN PAPAMETER OF THE PNEUMATIC CLIPPER

BJB11 DC SPEED SYNCHRONOUS PLATE BENDING MACHINE

This machine is drived by DC adjustable apeed motor.Normally it is working with peeling machine.

2M69 SERIESKNIFE GRINDER（WORKING TABLE WIDTH 200mm）

BG15 SERIES ROLLING GLIPPER

This equipment is a highly automatic equipment for the spindless veneer lathe and hydraulic double-chuck spindle veneer lathe. It is using numerical control system.

2MA69 SERIES KNIFE GRINDER

This machine is the necessary equipment for producingknife factory. It is applied to grinding the large size of part and knife. It has high efficiency and precision characteristic.

BQ12 SERIES HYDRAULIC SINGLE-CHUCK VENEER LATHE

BXQ11 SERIES SINGLE-CLAMP- SHAFT VENEER LATHE

this machine is mainly used to peel log with small diameter ， the main drive motor is AC motor or DC motor, which can be provided according to users request.

BQ 11 SERIES VENEER LATHE

BXQ16 SERIES HYDRAULIC DOUBLE CHUCK SPINDLE VENEER LATHE FOR SMALL DIAMETER LOG

this machine is a high quality, and efficiency veneer lathe for small log peeling.The main driver is advanced numerical controlled DC motor. The operation of the machine is program controlled. It can match with the projection block centering and charging machine and the synchronous reeling machine.

BQ16 SERIES HYDRAULIC DOUBLE CHUCK SPINDLE VEENEER LATHE

BXQS18 G/5 Series Large Wood Diameter Numerical Control Shaftless Rotary Cutting and Shearing Machine

This machine is used for the veneer peeling and shearing of large diameter wood after rounding. The wood core with a diameter of no more than Φ480mm can be peeled into veneers with different thicknesses of 1.0-3.0mm to improve the utilization rate of wood. It adopts advanced servo technology to control, make the cutting precision similar to the card rotary cutting machine, easy to use, can coopera

BXQS18 Series of small-diameter wood numerical control shaftless peeling machine (rotary shearing machine)

This machine is the main equipment of the plywood manufacturer. It is used for the peeling of the remaining wood core of the rotary cutting machine with a pinch and the rotary cutting of the veneer after the small diameter wood is rounded. The wood core with a diameter of not more than Φ400mm can be peeled into veneers with different thicknesses of 1.0-3.6mm to improve the utilization rate of wood

CNC non-card axis rotary cutting and shearing machine

This machine is mainly used for the rotary cutting of relatively large wood diameters, and can also be used for the rotary cutting of face plates. It adopts the working principle of the large-diameter wood rotary cutting machine with stuck shaft to make the rotary cutting accuracy more precise. Is the company's patented product, patent number: 4472995

넳 넲